TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was developed by two guys in California. They wanted to develop a cool writing instrument that appeared as if a real pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.
The Smok Pen has a built quality that is just great. I came across that even though it is an electronic pen the build quality is simply as good as the pens that I have reviewed. For the reason that of how they made the very best cap. You don’t need to worry about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens may be the form of the coils and just how that they are built. In general the coil on a Smok Pen is bigger than on other pens. I think that they did this on purpose, to make the pen feel bigger.
If you take a glance at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the back of the pen there is a little tab that houses the coil. Once you press on the tab you can easily turn the heating element on / off. I really liked this feature because it allows me to utilize the Smok Pen 22 whenever Personally i think like smoking.
To utilize the Smok Pen you need to vapinger.com keep the heat button pressed. Once the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature it is possible to turn off the heating element. Smok recommends using a 22mm tank. I prefer a larger tank, but that’s just me.
Once you put your Smok Pen in to the tank you will see a indicator light come on. The indicator light will remain green unless you put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is important to always put your pen into the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids in to the coil heads.
After you have completed this step, you should always check to see for anyone who is at the right temperature for the coils to fire. Or even then you should turn the power off and try again. Should you be still not satisfied with your Smok Pen then I suggest you take it in for some troubleshooting. This is what I would call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the following two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.
Prior to going any further you should remove the battery from your own pen and unscrew the magnetic cap. You need to then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You should loosen this wire using pliers. When you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it in to the Smok pen’s electrical port, being careful to not touch the coils.
After you have placed the sub-ohm tank in to the pen you need to then place all of those other components like the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Turn on the energy and follow the on screen instructions. You should place the pen’s battery in to the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it back off. When you initially put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it needs to reach you need to then connect both wires to the positive and negative on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to the bottom of the Smok’s power switch.
After all of the components have been placed in to the pen, you should turn the energy on. After the first test run, you need to be able to start to see the battery life indicator light seriously. If you don’t see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a fresh one. For your convenience gleam green light that may be pressed so that you can confirm the battery charging status. Once you have done these things and you do not start to see the green light indicating charging, you need to replace the battery.